My Quick start guide for Newbies to a great HFO session.
Posted: Sun Jul 21, 2019 9:53 pm
Here are some things that I do that end up with a HFO (Hands Free Orgasm) almost every single time:
1. Be in the mood. Bad day at work, fighting with your partner, not horny, got a headache? Maybe wait to try this tomorrow. This is the most important thing. Sometimes holding off from masturbating for a few days helps.
2. Take a shower. Every time before a session, this is a requirement. Getting your skin more moist will help prevent "shocking" feeling in the electrodes. I don't use electrogel, all though some recommend it, I'm fine without it if I take a shower, The shower also helps you relax, feel clean and get into the mood,
3. Use a butt electrode and insert it while in the shower. Use a good water based lube. I insert mine while in the shower. I cum harder if I have some type of butt electrode, especially if its pressing on my prostate. Personally I like E-Stim Systems Egg Medium for a more internal feel, but there are many plug types of out there. I like Bipolar plugs.
4. Use conductive rubber loops for males up front. I've tried metal, I've tried a lot of different types. The type that works best for me is the basic conductive loop. I wrap one around the base of the shaft with some type of clip holding the end. Next I take a 1/2 sized loop, wrap one part under the "head" and then one part over the middle like a straight line away from the body. I connect that part of the loop to the ring that is just under the head. I 3d printed some minimal holders, but you can do the same thing with glue (wait for it to dry before you try it!). It follows the shape of the "head" of the penis. The reason this is a shorter length is because I have the connector as close as possible.
5. Increase power slowly. I find a slow pulse mode or a mode that increase pulse until its solid works great. Slowly ramp this up. I've found setting the butt level one, to a level that just noticeable works great but allow the penis trode to go as high as needed. I often get to 60% on the penis trode before I explode.
Optional: Sometimes looking at porn is needed to help you get over the bump to a HFO.
Under Clothes:
I do almost all my stimming under clothes or costumes now. One thing that works great up front is to take a plastic grocery bag , take a corner thats not the handles, pull it though a circle you make with a thumb and your finger, pull out a length that is long enough for your penis, Cut the plastic to make a parachute shape. Wrap that around your penis and put it in your clothes. Not only will it catch all fluids it keeps your penis from contacting parts of your abdomen. Keep in mind the more you "leak" precum, the less effective the stim will feel, resulting in needing the raise the power level. This is also keeps you from having to use electrogel at higher levels, but you will need to take a shower first!. This works great from remote control setups ; )
1. Be in the mood. Bad day at work, fighting with your partner, not horny, got a headache? Maybe wait to try this tomorrow. This is the most important thing. Sometimes holding off from masturbating for a few days helps.
2. Take a shower. Every time before a session, this is a requirement. Getting your skin more moist will help prevent "shocking" feeling in the electrodes. I don't use electrogel, all though some recommend it, I'm fine without it if I take a shower, The shower also helps you relax, feel clean and get into the mood,
3. Use a butt electrode and insert it while in the shower. Use a good water based lube. I insert mine while in the shower. I cum harder if I have some type of butt electrode, especially if its pressing on my prostate. Personally I like E-Stim Systems Egg Medium for a more internal feel, but there are many plug types of out there. I like Bipolar plugs.
4. Use conductive rubber loops for males up front. I've tried metal, I've tried a lot of different types. The type that works best for me is the basic conductive loop. I wrap one around the base of the shaft with some type of clip holding the end. Next I take a 1/2 sized loop, wrap one part under the "head" and then one part over the middle like a straight line away from the body. I connect that part of the loop to the ring that is just under the head. I 3d printed some minimal holders, but you can do the same thing with glue (wait for it to dry before you try it!). It follows the shape of the "head" of the penis. The reason this is a shorter length is because I have the connector as close as possible.
5. Increase power slowly. I find a slow pulse mode or a mode that increase pulse until its solid works great. Slowly ramp this up. I've found setting the butt level one, to a level that just noticeable works great but allow the penis trode to go as high as needed. I often get to 60% on the penis trode before I explode.
Optional: Sometimes looking at porn is needed to help you get over the bump to a HFO.
Under Clothes:
I do almost all my stimming under clothes or costumes now. One thing that works great up front is to take a plastic grocery bag , take a corner thats not the handles, pull it though a circle you make with a thumb and your finger, pull out a length that is long enough for your penis, Cut the plastic to make a parachute shape. Wrap that around your penis and put it in your clothes. Not only will it catch all fluids it keeps your penis from contacting parts of your abdomen. Keep in mind the more you "leak" precum, the less effective the stim will feel, resulting in needing the raise the power level. This is also keeps you from having to use electrogel at higher levels, but you will need to take a shower first!. This works great from remote control setups ; )