New with Estim 2b

The most versatile and user friendly E-Stim control unit available today. If you want More Power, More Control, and more fun, then the 2B is the one you want.
Post Reply
feetinflips
Active
Posts: 6
Joined: Wed Dec 19, 2018 11:37 am
Location: Gzira

New with Estim 2b

Post by feetinflips » Wed Dec 19, 2018 11:47 am

I have purchased the Estim 2b device and started experimenting with the device. I' ve used 2 conductive rubber loops which where placed under my cock glans and at the base of my shaft. I've connected the lead as follows: on Channel A, red lead on the top loop and the black lead on the bottom loop.

The device was tested both of battery and also on with the power supplied. On both occasions I have noticed that I was not feeling anything between 1% and 50%. When connected through the power supply ove 50%, a good feeling was achieved but below that percentage there was no stimulation whatsoever.

Any advice please on how I could get the device to work on lower settings as well, please?

Thanks!



User avatar
Stimaddict
Active
Posts: 108
Joined: Wed Oct 25, 2017 11:56 am
Location: UK

Re: New with Estim 2b

Post by Stimaddict » Wed Dec 19, 2018 2:53 pm

Hi feetinflips - I saw your message on Smartstim and it seems your CR loops are the problem as it does not happen when you use TENS pads.
You need to use conductive gel with your loops and make sure they are tight so they make better contact with your skin.

feetinflips
Active
Posts: 6
Joined: Wed Dec 19, 2018 11:37 am
Location: Gzira

Re: New with Estim 2b

Post by feetinflips » Wed Dec 19, 2018 3:25 pm

Stimaddict wrote: ↑
Wed Dec 19, 2018 2:53 pm
Hi feetinflips - I saw your message on Smartstim and it seems your CR loops are the problem as it does not happen when you use TENS pads.
You need to use conductive gel with your loops and make sure they are tight so they make better contact with your skin.
Apparently it happened with the TENS pads too from 1% up to 35% I felt nothing. That is quite weird for a machine which is not so cheap!

feetinflips
Active
Posts: 6
Joined: Wed Dec 19, 2018 11:37 am
Location: Gzira

Re: New with Estim 2b

Post by feetinflips » Thu Dec 20, 2018 7:23 am

I've tested the TENS pads as well and they did not seem to work on low intensity either.

Any other advice will be greatly appreciated.

Thanks

User avatar
admin
Site Admin
Posts: 882
Joined: Tue Feb 19, 2008 8:14 pm
Location: Watford,UK
Contact:

Re: New with Estim 2b

Post by admin » Thu Dec 20, 2018 9:52 am

Not everyone is going to feel something at every level. Humans have a widely different range of sensitivity, so for some 35% is too much, for others its only the start. even at low levels its also dependant on the other settings at the moment, so the advice is experiment with positions of pads, and modes/levels.

Si
E-Stim Systems Ltd

User avatar
Stimaddict
Active
Posts: 108
Joined: Wed Oct 25, 2017 11:56 am
Location: UK

Re: New with Estim 2b

Post by Stimaddict » Thu Dec 20, 2018 2:10 pm

Try this...
  • Make sure you are using brand new TENS pads on clean skin. Don't use any lube or lotions.
  • Set your 2B to Hi-Power and plug in your mains adapter. Use only Channel A and select THROB mode.
  • Place one pad on top of your penis over or just below the glans.
    Hold it firmly in place with tape, straps or elastic bands.
  • Place the other pad behind your ball sack where it meets the perineum.
  • Slowly turn up the power on Channel A.
:?: At what level (on the LCD) do you start to feel sensation?
Last edited by Stimaddict on Thu Dec 20, 2018 2:20 pm, edited 3 times in total.

User avatar
Stimaddict
Active
Posts: 108
Joined: Wed Oct 25, 2017 11:56 am
Location: UK

Re: New with Estim 2b

Post by Stimaddict » Thu Dec 20, 2018 2:13 pm

  • Now turn the power up until it feels about right.
:?: What level are you at now?

Majorityon
Active
Posts: 42
Joined: Wed Aug 22, 2018 7:26 am
Location: East Anglia

Re: New with Estim 2b

Post by Majorityon » Fri Dec 21, 2018 11:07 am

What programme are you using? I find that Pgm 1, which pulses, only starts to be felt at quite a high level. Try Throb mode.

Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests