Page 1 of 2

Making a triphase configuration

Posted: Tue Aug 13, 2019 7:18 pm
by doomn2099
Hi, I want to make a triphase config but dont have the cable. My question is: can I connect the yellow cables from each cannel to each end of a rubber loop?. Also do I need to link the channels or can I still control the power of each cannel in triphase config. Also I would like to know in what position I put the elctrodes in a triphase config, I have rubber loops and a bipolar plug.
Thanks

Re: Making a triphase configuration

Posted: Wed Aug 14, 2019 12:49 pm
by Stimaddict
TriPhase, or a 3-Electrode Setup, is simply just this:
.
TriPhase2.jpg
.
Stim boxes use a kind of alternating current waveform so there is NO positive or negative. For the "Common" electrode you can connect two red cables, two blacks, or one red and one black. In your case you have different coloured cables but the principle is the same.
doomn2099 wrote: Tue Aug 13, 2019 7:18 pmcan I connect the yellow cables from each cannel to each end of a rubber loop?
Yes. If you are using a Conductive Rubber loop as the 'Common' electrode you don't need a TriPhase cable or adapter. Simply plug in two cables (one from each channel) into both ends of the CR tubing and you're good to go.
doomn2099 wrote: Tue Aug 13, 2019 7:18 pmAlso do I need to link the channels or can I still control the power of each cannel in triphase config.
You just use the two channels as normal and adjust the power of each channel separately to whatever levels you like.
doomn2099 wrote: Tue Aug 13, 2019 7:18 pmAlso I would like to know in what position I put the elctrodes in a triphase config, I have rubber loops and a bipolar plug.
You need to experiment with different options. Here is one example:
.
prostate trodes03.jpg
.
In this image (1) is the Common electrode - a CR loop just below the glans, (2) is your bipolar butt plug with just ONE wire connected, (3) is your second CR loop at the base of your cock.

Re: Making a triphase configuration

Posted: Fri Aug 16, 2019 2:52 pm
by zappy
Right, so with one of those conductive silicone tubes I can plug the two black electrodes in to each end of it to make the common electrode, right?

Re: Making a triphase configuration

Posted: Fri Aug 16, 2019 4:02 pm
by joannesReviews
Yes, that is correct.

Re: Making a triphase configuration

Posted: Sun Aug 18, 2019 7:24 pm
by gentlestimer
I love using my anal electrode, but its not always convenient. my go to tri-phase set up uses two loops and one large tens pad (5cm by 9cm).

the common is the pad, placed between my anus and ball sac. you have to do a bit of wire stripping to do this.

then, channel B at the base of my cock, and channel A just under the glands. Split A mode is great with this.

Re: Making a triphase configuration

Posted: Sun Aug 18, 2019 9:40 pm
by estimbird
You can also use a plug (for example a PenisPlug or MicroSound ) in a tri-phase-setup. Use the plug, a loop below the glans and another loop at the base. I can't really suggest a favourite position for the common electrode, just experiment a bit.

Re: Making a triphase configuration

Posted: Fri Jan 29, 2021 11:05 pm
by Ronfire7
To build a triphase cable is it best to connect the centre tap or the 2nd connector together to make 3 connections.
Will this be good for both a Pebble and a 2B?

Re: Making a triphase configuration

Posted: Sun Nov 26, 2023 10:38 pm
by shagmeraw
So if the following instructions for a stim audio file was as follows: Estim configuration is common (left- & right-) to head, left+ to shaft, right+ to under balls or lowest possible to shaft.

So channel A- one wire to head, Channel B- one wire to head. Then remaining channel wire from A to Base of shaft loop. And remaining Channel B to under Balls..
So if I have the estim systems Tri-phase cable. Could I put the Black on the Head as common . Then hook yellow and red to remaining [shaft] and under balls?
I have always been a little confused because the positive and negative with instruction. So thanks for clarifying
Thanks for your info StimAddict. Hope you get to feeling better soon

Re: Making a triphase configuration

Posted: Sat Dec 23, 2023 5:17 pm
by admin
And now our video about TriPhase

Re: Making a triphase configuration

Posted: Sun Dec 24, 2023 1:17 pm
by joannesReviews
I enjoyed that video; it was very informative and well done. The videos keep going from strength to strength.