Triphase

The forum for help regarding the new E-Stim Systems ElectroPebble. Have you got one? or thinking of purchasing one? Ask your questions here
Post Reply
appletartlet2
Newbie
Posts: 1
Joined: Tue Mar 07, 2017 1:31 pm
Location: UK

Triphase

Post by appletartlet2 » Tue Mar 07, 2017 1:54 pm

On the Electropebble can you connect the black plugs from the two channels onto opposite ends of the same conductive loop to create a triphase arrangement ?.



electrofun
Active
Posts: 24
Joined: Sun Jan 08, 2017 2:22 pm
Location: Belgium

Re: Triphase

Post by electrofun » Thu Jul 13, 2017 11:15 am

Yes, you could. I have tried similar setups and this works. Actually you don't have to connect the grounds together, as the ElectroPebble's outputs have the same ground (they are connected together in the box). So, connecting 1 ground should be enough.

A word of warning however: You would expect the black connector to be the ground (I did). Sometimes it's not. All 'normal' E-stim cables I have, have the black connector as ground, so that's good. On the E-stim 4mm 'low profile' cable however the yellow connector is ground, and the black is hot, I didn't expect this. I also have 2mm cables from other brands that have the red plug as ground and the black as hot, very confusing. So if things don't work as expected, you might try reversing connections. Or (that's what I did) check all your cables with an ohm- or continuity-meter and mark the 'wrong' ones.

User avatar
joannesReviews
Active
Posts: 48
Joined: Sat Apr 22, 2017 5:47 pm
Location: Derbyshire
Contact:

Re: Triphase

Post by joannesReviews » Fri Jul 14, 2017 12:26 pm

Excellent advice. I am going to have to try a Triphase set-up.

It sounds very interesting and I would like to see how it compares to just using two electrodes with one on each channel.

electrofun
Active
Posts: 24
Joined: Sun Jan 08, 2017 2:22 pm
Location: Belgium

Re: Triphase

Post by electrofun » Sat Jul 15, 2017 11:19 am

Be careful that triphase works differently, depending on the output configuration of the box you are using. My post above is for the ElectroPebble.
The series 1 has common ground like the ElectroPebble, but the 2 outputs also have the same signal and level, so there is no triphase effect.
The 2B has floating outputs, so there is no common ground between the 2 channels. So you have to connect them together yourself or use a triphase cable.

I have not (yet) tested this myself, but I think the difference in effect between triphase and two electrodes with one on each channel, will depend on the box you are using.

Have fun trying! - I know I do :)

Divebuddy
Active
Posts: 9
Joined: Fri Sep 01, 2017 7:36 am
Location: DE

Re: Triphase

Post by Divebuddy » Sun Sep 03, 2017 12:42 am

What are the advantages of the triphase-config (sorry if that is a newbie-question). From the schematics I would expect that I get Signal A, Signal B and something mixed from both?
How does that feel on a generic cockloop-setup?

electrofun
Active
Posts: 24
Joined: Sun Jan 08, 2017 2:22 pm
Location: Belgium

Re: Triphase

Post by electrofun » Thu Sep 21, 2017 11:28 pm

Difficult to describe how triphase feels, it depends very much on the setup, which box you use, etc. I'll describe 1 possible setup that I often use with the ElectroPebble:

Obviously you need 3 electrodes. If I use 1 circuit with a loop around my balls, and a loop around the glans, I feel it mostly on my glans and hardly anything on my balls. And I like the feeling of my balls being zapped :) The solution is this setup that I like very much: channel A (red) to my glans, channel B (red) to my balls, common (black) either to the central contact of a butt plug, or to electro pads on my abs or to electro pads on my thighs (I made some split cables to be able to connect 2 pads to the same circuit). This way I can control the intensity to my balls and to the penis separately and balance the feeling. Try it, it feels great :D

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest