I have purchased the Estim 2b device and started experimenting with the device. I' ve used 2 conductive rubber loops which where placed under my cock glans and at the base of my shaft. I've connected the lead as follows: on Channel A, red lead on the top loop and the black lead on the bottom loop.
The device was tested both of battery and also on with the power supplied. On both occasions I have noticed that I was not feeling anything between 1% and 50%. When connected through the power supply ove 50%, a good feeling was achieved but below that percentage there was no stimulation whatsoever.
Any advice please on how I could get the device to work on lower settings as well, please?
Thanks!
New with Estim 2b
-
- Active
- Posts: 24
- Joined: Wed Dec 19, 2018 11:37 am
- Location: Gzira
- Stimaddict
- Active Developer
- Posts: 991
- Joined: Wed Oct 25, 2017 11:56 am
- Location: UK
Re: New with Estim 2b
Hi feetinflips - I saw your message on Smartstim and it seems your CR loops are the problem as it does not happen when you use TENS pads.
You need to use conductive gel with your loops and make sure they are tight so they make better contact with your skin.
You need to use conductive gel with your loops and make sure they are tight so they make better contact with your skin.
-
- Active
- Posts: 24
- Joined: Wed Dec 19, 2018 11:37 am
- Location: Gzira
Re: New with Estim 2b
Apparently it happened with the TENS pads too from 1% up to 35% I felt nothing. That is quite weird for a machine which is not so cheap!Stimaddict wrote: ↑Wed Dec 19, 2018 2:53 pm Hi feetinflips - I saw your message on Smartstim and it seems your CR loops are the problem as it does not happen when you use TENS pads.
You need to use conductive gel with your loops and make sure they are tight so they make better contact with your skin.
-
- Active
- Posts: 24
- Joined: Wed Dec 19, 2018 11:37 am
- Location: Gzira
Re: New with Estim 2b
I've tested the TENS pads as well and they did not seem to work on low intensity either.
Any other advice will be greatly appreciated.
Thanks
Any other advice will be greatly appreciated.
Thanks
- admin
- Site Admin
- Posts: 2121
- Joined: Tue Feb 19, 2008 8:14 pm
- Location: Watford,UK
- Contact:
Re: New with Estim 2b
Not everyone is going to feel something at every level. Humans have a widely different range of sensitivity, so for some 35% is too much, for others its only the start. even at low levels its also dependant on the other settings at the moment, so the advice is experiment with positions of pads, and modes/levels.
Si
Si
E-Stim Systems Ltd
- Stimaddict
- Active Developer
- Posts: 991
- Joined: Wed Oct 25, 2017 11:56 am
- Location: UK
Re: New with Estim 2b
Try this...
- Make sure you are using brand new TENS pads on clean skin. Don't use any lube or lotions.
- Set your 2B to Hi-Power and plug in your mains adapter. Use only Channel A and select THROB mode.
- Place one pad on top of your penis over or just below the glans.
Hold it firmly in place with tape, straps or elastic bands.
- Place the other pad behind your ball sack where it meets the perineum.
- Slowly turn up the power on Channel A.
Last edited by Stimaddict on Thu Dec 20, 2018 2:20 pm, edited 3 times in total.
- Stimaddict
- Active Developer
- Posts: 991
- Joined: Wed Oct 25, 2017 11:56 am
- Location: UK
Re: New with Estim 2b
- Now turn the power up until it feels about right.
-
- Active
- Posts: 51
- Joined: Wed Aug 22, 2018 7:26 am
- Location: East Anglia
Re: New with Estim 2b
What programme are you using? I find that Pgm 1, which pulses, only starts to be felt at quite a high level. Try Throb mode.