Hello all.
I will start this question as just that a question and hopefully not a stupid one. I am loving my 2B but decided I was going to do the upgrade. Latest version is out and I’m on one step older so I thought I would just upgrade. In trying to install the uplink software and drivers I have hit a roadblock. I have Tried to install these programs from the USB stick on three separate computers. All three computers refuse to allow me to install any of these drivers or programs. Now I admit I am not super computer savvy but I have built these things and I work on computers every day at work. So I kind a know my way around on computers. But this is getting frustrating. It either tells me it cannot create the folder when I go to unzip the files, or he gives me some unknown error code and stops the install. I can’t figure this out I figured my small portable laptop Was probably the cause because it’s cheap and has a slower processor. Truthfully it’s faster than the computer at work because the one that work is so loaded down with crap but even my wife’s laptop won’t load it either I did copy the error code I took a picture of it. But it just says unknown gives me a bunch of numbers. I’ll upload the picture hopefully somebody can decipher this and tell me what I’m doing wrong. I seriously doubt but then I guess that is possible that my USB stick may be defective or corrupt. I even tried to copy the entire contents onto my C Drive and install it directly from there but that works neither.
I hope someone can help. thank you in advance
Kenny.
Installing the software to do the upgrades and commander on your laptop
- KennyT
- Active
- Posts: 84
- Joined: Sun Aug 13, 2017 3:40 pm
- Location: Florida, USA
- Contact:
Installing the software to do the upgrades and commander on your laptop
You do not have the required permissions to view the files attached to this post.
KennyT
- admin
- Site Admin
- Posts: 2121
- Joined: Tue Feb 19, 2008 8:14 pm
- Location: Watford,UK
- Contact:
Re: Installing the software to do the upgrades and commander on your laptop
The Error is a windows error which appears to be related to windows product activation on windows XP, or file permissions on Windows 10
what version of windows are you running?
you might need to google the error code and try some of the solutions other have been using as it appears to . be a windows issue, rather than specific to Uplink.
Normally it is a case of copy files to desktop, extract and run.
Si
what version of windows are you running?
you might need to google the error code and try some of the solutions other have been using as it appears to . be a windows issue, rather than specific to Uplink.
Normally it is a case of copy files to desktop, extract and run.
Si
E-Stim Systems Ltd
- KennyT
- Active
- Posts: 84
- Joined: Sun Aug 13, 2017 3:40 pm
- Location: Florida, USA
- Contact:
Re: Installing the software to do the upgrades and commander on your laptop
I am running windows 10 64 bit. It was just installed about 2 months ago when I did upgrades to my laptop.
I installed Winrar this morning and tried installing it this way and got a slew of new warnings that all the files on the usb stick are corrupt. I will post this picture also.
I was hoping maybe i could get the files sent to me through email and I can format the usb stick and reinstall them there and try again...
I haven't ever used the USB stick until now so I cant figure I corrupted it but who knows. I just want to upgrade my box. and I did purchase it from E-stim systems. I think it was June last year. I can dig it up on the web orders if needed.
I never dreamed I would have this much trouble
Ken
I installed Winrar this morning and tried installing it this way and got a slew of new warnings that all the files on the usb stick are corrupt. I will post this picture also.
I was hoping maybe i could get the files sent to me through email and I can format the usb stick and reinstall them there and try again...
I haven't ever used the USB stick until now so I cant figure I corrupted it but who knows. I just want to upgrade my box. and I did purchase it from E-stim systems. I think it was June last year. I can dig it up on the web orders if needed.
I never dreamed I would have this much trouble
Ken
You do not have the required permissions to view the files attached to this post.
KennyT
- Stimaddict
- Active Developer
- Posts: 991
- Joined: Wed Oct 25, 2017 11:56 am
- Location: UK
Re: Installing the software to do the upgrades and commander on your laptop
I think your USB stick is f**ked. Not the stick's fault, this can happen with any USB memory and the only way to fix it is to reformat and lose the data. PM sent.
- admin
- Site Admin
- Posts: 2121
- Joined: Tue Feb 19, 2008 8:14 pm
- Location: Watford,UK
- Contact:
Re: Installing the software to do the upgrades and commander on your laptop
E-Stim Systems Ltd
- KennyT
- Active
- Posts: 84
- Joined: Sun Aug 13, 2017 3:40 pm
- Location: Florida, USA
- Contact:
Re: Installing the software to do the upgrades and commander on your laptop
Thank you for your help It is appreciated .. This is why I love this forum..
KennyT
- KennyT
- Active
- Posts: 84
- Joined: Sun Aug 13, 2017 3:40 pm
- Location: Florida, USA
- Contact:
Re: Installing the software to do the upgrades and commander on your laptop
All problems are fixed now. Got the files and I had a bad USB stick from the start.
USB stick is toast
Put all files on a new stick and im updated to the newest firmware.
up and running
THANKS ALL FOR YOUR HELP
USB stick is toast
Put all files on a new stick and im updated to the newest firmware.
up and running
THANKS ALL FOR YOUR HELP
KennyT