The bounce trick with Waterfall and Wave
Posted: Wed Jan 26, 2022 12:14 pm
This is my goto when using my 2B So I thought I would share this just encase others have not worked it out yet. Or for anyone new.
You will need to setup with a tri phrase configuration. however the trick is to setup your electrodes so that they give a similar level of sensation to each other.
Config 1. 3 cock loops. One on the just above the glans one on the centre shaft one on the base of the shafe. The centre you connect both Black plugs to. then the yellows one to the shaft then one to the glans. You may need to experiment with the placement of the loop in the middle. Even a small shift either way up or down the shaft can change the intensity.
Config 2 butt plug/ Pad or cock loop / Urethral Sound. You may need a tri cable for this if your using a pad. Or you could just use 2 pads. The Urethral Sound and butt plug would go where you would expect them to go. If your using 1 pad it will go either under balls or on the shaft. You can experiment with putting the pad on the top or under side of the shaft you can also experiment with changing the black cables between the two pads to give different sensations. You can put the loop around the shaft or around the shaft and under the balls. There is a lot of configurations to experiment with this one.
Mode settings
This is all about timing so start with the speed at about 80 ( 80 50 ) set the output of A and B channels at the same level to where you feel comfortable but give yourself some head room. Now increase one of the levels by about 2 % and wait. You should feel the overall output drop and one channel will start to drift out of time with each other. when you feel the pulses of channel 1 and 2 to be evenly apart set the output of both channels the same. This will lock both channels to the same pulse giving a rather nice bounce.
You can use the speed to increase to speed of the pulse you can use the feel which will not put the pulse out of time and as long as you have your controls locked so one of them is set to bring both levels up you can ramp up the current without putting your pulses out of sync.
This will work on wave and waterfall the same way.
Enjoy
You will need to setup with a tri phrase configuration. however the trick is to setup your electrodes so that they give a similar level of sensation to each other.
Config 1. 3 cock loops. One on the just above the glans one on the centre shaft one on the base of the shafe. The centre you connect both Black plugs to. then the yellows one to the shaft then one to the glans. You may need to experiment with the placement of the loop in the middle. Even a small shift either way up or down the shaft can change the intensity.
Config 2 butt plug/ Pad or cock loop / Urethral Sound. You may need a tri cable for this if your using a pad. Or you could just use 2 pads. The Urethral Sound and butt plug would go where you would expect them to go. If your using 1 pad it will go either under balls or on the shaft. You can experiment with putting the pad on the top or under side of the shaft you can also experiment with changing the black cables between the two pads to give different sensations. You can put the loop around the shaft or around the shaft and under the balls. There is a lot of configurations to experiment with this one.
Mode settings
This is all about timing so start with the speed at about 80 ( 80 50 ) set the output of A and B channels at the same level to where you feel comfortable but give yourself some head room. Now increase one of the levels by about 2 % and wait. You should feel the overall output drop and one channel will start to drift out of time with each other. when you feel the pulses of channel 1 and 2 to be evenly apart set the output of both channels the same. This will lock both channels to the same pulse giving a rather nice bounce.
You can use the speed to increase to speed of the pulse you can use the feel which will not put the pulse out of time and as long as you have your controls locked so one of them is set to bring both levels up you can ramp up the current without putting your pulses out of sync.
This will work on wave and waterfall the same way.
Enjoy