write own sequence
Posted: Thu Jan 11, 2024 5:51 pm
Hi there,
I am new here, but not new to estim. HFO is a well known thing for me but I love the principle "before pleasure comes edging". A lot...and very long
In the past i used 2 mystim tension lovers in combination with a programmable power socket und timer relays to create sequences in which each tens untit runs in a loop e.g.
Tens Unit A
2 minutes on (signal programm X 7 seconds on, 8 seconds off)
2 minute off
2 minutes on (signal programm X 7 seconds on, 8 seconds off)
2 min off
pause 2 minutes
Tens Unit B
2 minute off
2 minutes on (signal programm Y 7 seconds on, 8 seconds off)
2 minute off
2 minutes on (signal programm Y 7 seconds on, 8 seconds off)
pause 2 minutes
The minutes loop I create with the programmable power socket which just cuts the power and then switches on as programmed.
The seconds loop I create with a time relay between the power socket and the tens unit.
Programm, power, strength...etc. is set to bring me close to orgasm, but without release which drives you crazy after a while.
Once started and locked into selfbondage (in combination with a time release) and everything out of reach there is no way to change anything and brings you close to a status in which you really desperatly want to come but can`t.
BTW: With the mystim tension lover this works ONLY because the power AFTER each restart starts with 0 and ramps within 2-3 seconds to the set level, like a inbuild ramp-modus.
Now I want a similar outcome with a 2B but based on the given infos I can´t see clearly how:
AFAIK there is no inbuild ramp when turning on the 2B therefore I would like to skip the turning off and on again power completely in my scenario.
This leads me to the comander software and its possibilities.
Is there a way to create time sequences in which a set programm e.g. throb, squeeze or waterfall can be made to run like descibed above? And what are the time limits or is it possible to combine different/same time sequences one after another.
Maybe someone already tried a similar scenario and could give me some idear/how to...or is there a tutorial how to programme sequences with the command software?
Greetings
I am new here, but not new to estim. HFO is a well known thing for me but I love the principle "before pleasure comes edging". A lot...and very long
In the past i used 2 mystim tension lovers in combination with a programmable power socket und timer relays to create sequences in which each tens untit runs in a loop e.g.
Tens Unit A
2 minutes on (signal programm X 7 seconds on, 8 seconds off)
2 minute off
2 minutes on (signal programm X 7 seconds on, 8 seconds off)
2 min off
pause 2 minutes
Tens Unit B
2 minute off
2 minutes on (signal programm Y 7 seconds on, 8 seconds off)
2 minute off
2 minutes on (signal programm Y 7 seconds on, 8 seconds off)
pause 2 minutes
The minutes loop I create with the programmable power socket which just cuts the power and then switches on as programmed.
The seconds loop I create with a time relay between the power socket and the tens unit.
Programm, power, strength...etc. is set to bring me close to orgasm, but without release which drives you crazy after a while.
Once started and locked into selfbondage (in combination with a time release) and everything out of reach there is no way to change anything and brings you close to a status in which you really desperatly want to come but can`t.
BTW: With the mystim tension lover this works ONLY because the power AFTER each restart starts with 0 and ramps within 2-3 seconds to the set level, like a inbuild ramp-modus.
Now I want a similar outcome with a 2B but based on the given infos I can´t see clearly how:
AFAIK there is no inbuild ramp when turning on the 2B therefore I would like to skip the turning off and on again power completely in my scenario.
This leads me to the comander software and its possibilities.
Is there a way to create time sequences in which a set programm e.g. throb, squeeze or waterfall can be made to run like descibed above? And what are the time limits or is it possible to combine different/same time sequences one after another.
Maybe someone already tried a similar scenario and could give me some idear/how to...or is there a tutorial how to programme sequences with the command software?
Greetings