www.e-stim.net

Hello, I am interested in the Seriouskit, Daft Punk harness kit. Does anyone have experience with this and can tell me whether it feels different under a vacuum?
I'm currently only using the loops with the Estim system 2b 2.126 Beta

Hello & welcome.
I can only answer in part. I recently bought the Serious Kit (SK) Polished ring vacuum cylinder and enjoy hand pumping with E-Stim. Yesterday the "T" leather harness & Perineal Electrode arrived. I have only had a short test run & all seems good. The "Daft Punk" pump & stim kit may be next on my list. I am hoping to use my SK vacuum cylinder with my T harness & Perineal electrode plus the E-Stim Large Deviant insertable. Watch this space for further developments.

thanks for the reply. then I'm looking forward to further developments.

Update on the use of the Serious Kit "T" Leather harness & Perineal Electrode. As you would expect from this company, the harness is quality stretchy leather with sturdy buckles. The hole at the front is for your cock, but I can get my balls through as well. The electrode is polished aluminium and can be positioned in three positions. I found just strapping the harness on was a thrill! My next concern was would the electrode need any lube to prevent hot spots. So far I think it is okay with or without lube. As my skin sometimes reacts badly to sticky pads, it is nice to use this perineum metal electrode.
I started with my 2-B on mains power & A-Split, the other pad on my cock. Very nice at many different settings. Later, I managed to insert the Large Deviant which the harness will hold in place. Note, I used a small cable adaptor with right angle connections out the side of the harness. Then with my E-Stim Tri-phase cable all three electrodes could be connected. The 2-B is set on High Power & lots of fun can be had with both A&B channels in use. My next trial will be to try & use the vacuum pump cylinder.

Thanks for the exciting feedback. Now I'm excited about the vacuum cylinder

VFRman wrote: ↑Sun Mar 03, 2024 9:58 am Update on the use of the Serious Kit "T" Leather harness & Perineal Electrode. As you would expect from this company, the harness is quality stretchy leather with sturdy buckles. The hole at the front is for your cock, but I can get my balls through as well. The electrode is polished aluminium and can be positioned in three positions. I found just strapping the harness on was a thrill! My next concern was would the electrode need any lube to prevent hot spots. So far I think it is okay with or without lube. As my skin sometimes reacts badly to sticky pads, it is nice to use this perineum metal electrode.
I started with my 2-B on mains power & A-Split, the other pad on my cock. Very nice at many different settings. Later, I managed to insert the Large Deviant which the harness will hold in place. Note, I used a small cable adaptor with right angle connections out the side of the harness. Then with my E-Stim Tri-phase cable all three electrodes could be connected. The 2-B is set on High Power & lots of fun can be had with both A&B channels in use. My next trial will be to try & use the vacuum pump cylinder.

Keep us posted !!

Good day to my Dutch & German stimming friends. A few days ago I got all ready for a nice session with my Serious Kit (SK) T leather harness, with the Aluminium perineum electrode. So far so good. The difficulty is trying to use the SK Polished cylinder. I do not think this is designed for that, but I managed to push it through (very tight) the centre hole. The next problem is trying to pump with a good seal. My balls get squashed by the strap so I pulled them out the side! Not perfect but I managed to make a seal so my cock could get a pump to the second ring allowing me to stim. Then trying to insert my Large Torpedo, which would give me a total of 4 points to connect using the Tri-Phase cable. All this fitting & adjustment was too much to do and spoilt the session. Had a standard cum with pads & my wand (Doxy)
This is going to be work in progress. I may try with a standard vacuum cylinder. If you check the SK web you will see alternative kits for the T harness.

VFRman wrote: ↑Fri Mar 15, 2024 5:02 pm Good day to my Dutch & German stimming friends. A few days ago I got all ready for a nice session with my Serious Kit (SK) T leather harness, with the Aluminium perineum electrode. So far so good. The difficulty is trying to use the SK Polished cylinder. I do not think this is designed for that, but I managed to push it through (very tight) the centre hole. The next problem is trying to pump with a good seal. My balls get squashed by the strap so I pulled them out the side! Not perfect but I managed to make a seal so my cock could get a pump to the second ring allowing me to stim. Then trying to insert my Large Torpedo, which would give me a total of 4 points to connect using the Tri-Phase cable. All this fitting & adjustment was too much to do and spoilt the session. Had a standard cum with pads & my wand (Doxy)
This is going to be work in progress. I may try with a standard vacuum cylinder. If you check the SK web you will see alternative kits for the T harness.

Thank you for the feedback, it doesn't sound so good at first. Have you tried a different cylinder?

I have been experimenting with pump&stim for some time now.
I have not yet understood the function of the aluminium hand pump cylinder.
If I read it correctly on the SK website, the penis should have full-surface contact with the inner wall of the cylinder when pumped.
However, this would distribute the current stimulus over the entire surface of the penis or the current would find the path of least resistance and pass from the aluminium cylinder into the tissue in a ring at the base of the penis.
Where is the electrostimulation felt then?

Thank you for your wealth of experience!

Hi Deltus & friends
Always nice to get a reply, especially with a question. First I will explain about using the Serious Kit (SK), Polished ring cylinder. On its own. To order you need to measure the diameter of your cock when fully erect. In my case, I cannot get a good full hard anymore so I used another plain cylinder to pump up fully & then remove & tie with a small rope, tight all around the base. Cock & balls. Then measure. I think the average for most will be within the range SK offer. In my case my cock, about 30mm down from the head tip is where I want the second ring to be. And the diameter is 40mm.

Now the first stainless steel ring (the base) that diameter is 50mm. So my procedure is to lube my cock and some lube around the base, insert (semi slack) my cock, rotate, back & forth against my skin to make a seal, then start pumping. It sometimes need a little downwards pressure to seal, but once sealed you continue pumping until my cock head pops through the second ring, which will be tight. I pump so that the ring is against the shaft where I like it. Now to stimming. To start I use my 2-B on high power & A-Split (240v mains) mono cable one pad under balls on the Perineum. Connect one lead to this & the other I start, connected to the First Ring on the cylinder. Start settings (default) 50/50, turn some power up, let the nerves settle then experiment with higher power & different Adjust Settings, like 61/58, 91/61 & all the many variations in between. After a while enjoying the sensations, I change to the Second (upper) Ring. Now this will be very different & much more sensitive. Of course, do not forget to turn off the power before changing rings. No the whole shaft will not be stimulated unless you connect both cables, one to bottom, the other to top. I do not like that.

lastly. The SK product is expensive, but you get what you pay for. It is superbly engineered. I could send you photos if you PM me.