Making a triphase configuration
-
- Newbie
- Posts: 3
- Joined: Thu May 30, 2019 7:32 am
- Location: Puerto Rico
Making a triphase configuration
Hi, I want to make a triphase config but dont have the cable. My question is: can I connect the yellow cables from each cannel to each end of a rubber loop?. Also do I need to link the channels or can I still control the power of each cannel in triphase config. Also I would like to know in what position I put the elctrodes in a triphase config, I have rubber loops and a bipolar plug.
Thanks
Thanks
- Stimaddict
- Active Developer
- Posts: 1023
- Joined: Wed Oct 25, 2017 11:56 am
- Location: UK
Re: Making a triphase configuration
TriPhase, or a 3-Electrode Setup, is simply just this:
. .
Stim boxes use a kind of alternating current waveform so there is NO positive or negative. For the "Common" electrode you can connect two red cables, two blacks, or one red and one black. In your case you have different coloured cables but the principle is the same.
. .
In this image (1) is the Common electrode - a CR loop just below the glans, (2) is your bipolar butt plug with just ONE wire connected, (3) is your second CR loop at the base of your cock.
. .
Stim boxes use a kind of alternating current waveform so there is NO positive or negative. For the "Common" electrode you can connect two red cables, two blacks, or one red and one black. In your case you have different coloured cables but the principle is the same.
Yes. If you are using a Conductive Rubber loop as the 'Common' electrode you don't need a TriPhase cable or adapter. Simply plug in two cables (one from each channel) into both ends of the CR tubing and you're good to go.
You just use the two channels as normal and adjust the power of each channel separately to whatever levels you like.
You need to experiment with different options. Here is one example:
. .
In this image (1) is the Common electrode - a CR loop just below the glans, (2) is your bipolar butt plug with just ONE wire connected, (3) is your second CR loop at the base of your cock.
You do not have the required permissions to view the files attached to this post.
-
- Active
- Posts: 5
- Joined: Fri Aug 16, 2019 2:29 pm
- Location: UK
Re: Making a triphase configuration
Right, so with one of those conductive silicone tubes I can plug the two black electrodes in to each end of it to make the common electrode, right?
- joannesReviews
- Active Developer
- Posts: 431
- Joined: Sat Apr 22, 2017 5:47 pm
- Location: Derbyshire, UK
- Contact:
Re: Making a triphase configuration
Yes, that is correct.
Just a woman in her 50s who likes e-stim and sticking things in her pussy while telling the world all about it on my review site. I'm quite normal, I think LOL.
-
- Active
- Posts: 7
- Joined: Sun Aug 11, 2019 12:57 am
- Location: ontario
Re: Making a triphase configuration
I love using my anal electrode, but its not always convenient. my go to tri-phase set up uses two loops and one large tens pad (5cm by 9cm).
the common is the pad, placed between my anus and ball sac. you have to do a bit of wire stripping to do this.
then, channel B at the base of my cock, and channel A just under the glands. Split A mode is great with this.
the common is the pad, placed between my anus and ball sac. you have to do a bit of wire stripping to do this.
then, channel B at the base of my cock, and channel A just under the glands. Split A mode is great with this.
-
- Active Developer
- Posts: 229
- Joined: Tue Aug 28, 2018 7:48 pm
- Location: Germany
Re: Making a triphase configuration
You can also use a plug (for example a PenisPlug or MicroSound ) in a tri-phase-setup. Use the plug, a loop below the glans and another loop at the base. I can't really suggest a favourite position for the common electrode, just experiment a bit.
- Ronfire7
- Active Developer
- Posts: 197
- Joined: Tue Dec 08, 2020 2:35 am
- Location: Merritt BC Canada
Re: Making a triphase configuration
To build a triphase cable is it best to connect the centre tap or the 2nd connector together to make 3 connections.
Will this be good for both a Pebble and a 2B?
Will this be good for both a Pebble and a 2B?
-
- Active
- Posts: 5
- Joined: Sat Sep 30, 2023 12:55 pm
- Location: united states
Re: Making a triphase configuration
So if the following instructions for a stim audio file was as follows: Estim configuration is common (left- & right-) to head, left+ to shaft, right+ to under balls or lowest possible to shaft.
So channel A- one wire to head, Channel B- one wire to head. Then remaining channel wire from A to Base of shaft loop. And remaining Channel B to under Balls..
So if I have the estim systems Tri-phase cable. Could I put the Black on the Head as common . Then hook yellow and red to remaining [shaft] and under balls?
I have always been a little confused because the positive and negative with instruction. So thanks for clarifying
Thanks for your info StimAddict. Hope you get to feeling better soon
So channel A- one wire to head, Channel B- one wire to head. Then remaining channel wire from A to Base of shaft loop. And remaining Channel B to under Balls..
So if I have the estim systems Tri-phase cable. Could I put the Black on the Head as common . Then hook yellow and red to remaining [shaft] and under balls?
I have always been a little confused because the positive and negative with instruction. So thanks for clarifying
Thanks for your info StimAddict. Hope you get to feeling better soon
- admin
- Site Admin
- Posts: 2168
- Joined: Tue Feb 19, 2008 8:14 pm
- Location: Watford,UK
- Contact:
- joannesReviews
- Active Developer
- Posts: 431
- Joined: Sat Apr 22, 2017 5:47 pm
- Location: Derbyshire, UK
- Contact:
Re: Making a triphase configuration
I enjoyed that video; it was very informative and well done. The videos keep going from strength to strength.
Just a woman in her 50s who likes e-stim and sticking things in her pussy while telling the world all about it on my review site. I'm quite normal, I think LOL.