First impressions
Posted: Thu Aug 22, 2019 8:59 am
Hi all,
I received the 2b box one week ago, and yet didn’t have any opportunity to test it at the best conditions. This might happen in the next few days.
For now I had only some occasions to try the box only a short time. I only used the elements delivered with the box (9V, patches) and no extra (which I ordered but didn’t received yet).
I can anyway tell about the very first impressions! Due to the bad conditions I was not able to be “hard”. I knew that was going to be complicate. The temperature was to warm, I wasn’t really relaxed, but I had to try.
I used only one channel, with 2 patches on it. One under the glan and one at the base of the penis. Since I was not in erection, the patches were almost touching each other -they look small on the photos but in reality they are quite big, 2 of them make almost 9 cm which is quite long for a penis without erection-.
Anyway I went forward, took care to avoid any contact between the patches. This did add a bit more stress to the already not relaxed situation. I plugged the 9V in the box, plugged all the needed cables where it had to go (which is not complicate at all) and switched on.
After few seconds, the screen finally shows the usual mode, letter A/B and so on. I have been reading few topics here so I decided to jump directly on throb mode, and slowly turned the A level.
From 10-12% I started to feel a small thing, that was new to me. The patches were good on place, but the penis had something like “what are you doing now”. After few seconds, I saw that it would been problematic to be at this non-erected condition, but I wanted to see forward. I moved the level up and up. I started to play with the modes. And from 25% it began to feel really strong! I barely could go over this amount (if I remember, I could go until 60% only on one mode). This was with 9V and I started to think, what the hell is this machine! I’m not yet on the half of the power with a 9V!
It felt quite picky, but still it was acceptable, I could feel the pleasure already and pre-cum came already. It felt quite “mechanical”, like somebody forcing you to have an orgasm at a moment when you absolutely don’t want it. I am sure that wouldn’t be an issue if I was erected and using conductive rubber loops. I had again another try in the same uncomfortable conditions but with the adaptor, with my penis that was a bit more erected but still was not enough.
For now I see the importance of having the right conditions: 1- room temperature. 2- position (bed, couch). 3- comfortable situation (need free time, I would say think about 3 hours of time to feel relax). 4- erected penis (with the 3 previous points and some entertainment that shouldn’t be an issue). 5- don’t panic with using 9V: it’s more than enough for a first try!. 6- consider cutting the patches. In my opinion they are to big.
That are my very first impressions! I hope this can help anyone thinking about purchasing the box.
I received the 2b box one week ago, and yet didn’t have any opportunity to test it at the best conditions. This might happen in the next few days.
For now I had only some occasions to try the box only a short time. I only used the elements delivered with the box (9V, patches) and no extra (which I ordered but didn’t received yet).
I can anyway tell about the very first impressions! Due to the bad conditions I was not able to be “hard”. I knew that was going to be complicate. The temperature was to warm, I wasn’t really relaxed, but I had to try.
I used only one channel, with 2 patches on it. One under the glan and one at the base of the penis. Since I was not in erection, the patches were almost touching each other -they look small on the photos but in reality they are quite big, 2 of them make almost 9 cm which is quite long for a penis without erection-.
Anyway I went forward, took care to avoid any contact between the patches. This did add a bit more stress to the already not relaxed situation. I plugged the 9V in the box, plugged all the needed cables where it had to go (which is not complicate at all) and switched on.
After few seconds, the screen finally shows the usual mode, letter A/B and so on. I have been reading few topics here so I decided to jump directly on throb mode, and slowly turned the A level.
From 10-12% I started to feel a small thing, that was new to me. The patches were good on place, but the penis had something like “what are you doing now”. After few seconds, I saw that it would been problematic to be at this non-erected condition, but I wanted to see forward. I moved the level up and up. I started to play with the modes. And from 25% it began to feel really strong! I barely could go over this amount (if I remember, I could go until 60% only on one mode). This was with 9V and I started to think, what the hell is this machine! I’m not yet on the half of the power with a 9V!
It felt quite picky, but still it was acceptable, I could feel the pleasure already and pre-cum came already. It felt quite “mechanical”, like somebody forcing you to have an orgasm at a moment when you absolutely don’t want it. I am sure that wouldn’t be an issue if I was erected and using conductive rubber loops. I had again another try in the same uncomfortable conditions but with the adaptor, with my penis that was a bit more erected but still was not enough.
For now I see the importance of having the right conditions: 1- room temperature. 2- position (bed, couch). 3- comfortable situation (need free time, I would say think about 3 hours of time to feel relax). 4- erected penis (with the 3 previous points and some entertainment that shouldn’t be an issue). 5- don’t panic with using 9V: it’s more than enough for a first try!. 6- consider cutting the patches. In my opinion they are to big.
That are my very first impressions! I hope this can help anyone thinking about purchasing the box.